Gerai Produk - Pusat Produk Indonesia www.geraiproduk.com

Sanwa DCM400 & DCM60L Digital AC Clamp Meter

chris — Fri, 24 Oct 2008 08:59:43 +0000

Sanwa DCM400 & DCM60L Digital AC Clamp Meter
DCM400
-Auto range
-Frequency measurement by clamp or test leads
-Data hold
-Range hold
-Cont. buzzer
-Auto power off
-Low power indication

DCM60L
-Data hold
-Low power indication
-Auto range
-Cont. buzzer

DCM400.jpg

DCM60L.jpg

Hioki 3286-20 Digital Clamp On Power HiTester

chris — Mon, 27 Apr 2009 13:19:46 +0000

Hioki 3286-20 Digital Clamp On Power HiTester

Features :
* Use as a single-phase power meter
* Measure phase on a single-phase line
* Simple checking of three-phase lines
* Check power supply fluctuations
* For harmonic suppression
* External output of data to PC
* Printer output to 9442 (optional)

Specifications :
Measurement lines : Single-phase/two-wires, Three-phase/three-wires (balanced load only)
Measurement items : Voltage, current, voltage/current peak, effective/reactive/apparent power(Single-phase or 3-phase), power factor, reactivity, phase angle, frequency, phase detection(3-phase), voltage/current harmonic levels(up to 20th)
Measurement ranges
Voltage : 150.0 V to 600 V, 3 ranges, Current: 20.00 to 1000 A, 3 ranges, Power: 3.000 kW to 1200 kW, 18 combination patterns, Note: 3-phase power is calculated and displayed on the basis of a balanced, 50/60 Hz, sine wave input. For apparent power and reactive power, the unit of watts in the above table is replaced by VA and var respectively.
Basic accuracy at 50/60 Hz, COS Ø=1
Power/single-phase: ±2.3 % rdg. ±5 dgt., Power/3-phase: ±3.0 % rdg. ±10 dgt. (at balanced load)
Voltage / Current accuracy : Voltage: ±1.0 % rdg. ±3 dgt., Current: ±1.3 % rdg. ±3 dgt. (at 45 to 66 Hz)
Frequency characteristics
AC current : 45 to 1 kHz
AC voltage : 30 to 1 kHz
Other functions : Phase detection, Record (Max. value/Min. value), Battery capacity display, Data hold, Auto power off, Data output (RS-232C interface by optical insulating coupler)
Display update rate : NORMAL: approx. 1 time/ sec, SLOW: 1 time/ 3-sec, HARM meas.: approx. 1 time/ 2-sec
Power supply : 6LR61 alkaline battery × 1 (continuous operation max. 25 hours), 6F22 manganese battery × 1 (continuous operation max. 10 hours)
Dimensions, mass : 100 mm(3.94 in)W × 287 mm(11.3 in)H × 39 mm(1.54 in)D, 650 g (22.6 oz) Core jaw dia.: Ø55 mm(2.17 in) or 80 mm (3.15 in) × 20 mm (0.79 in) busbar
Accessories : VOLTAGE CORD 9635 (1), CARRYING CASE 9245, (1), Hand strap (1)

hioki-3286-20.jpg

Protek 6502A - 20 MHz Analog Oscilloscope

chris — Sat, 03 Oct 2009 14:56:39 +0000

Protek 6502A - 20 MHz Analog Oscilloscope

Fitur:
2 Channel 4 Trace
20MHz Bandwidth
X5 Magnifier
ALT Trigger

Spesifikasi:
http://www.hcqelectronic.com/EN/products_info.aspx?id=82&type=3

protek_6502a.jpg

Fluke Digital ScopeMeter® 120 Series

chris — Tue, 20 Oct 2009 16:04:11 +0000

Fluke Digital ScopeMeter® 120 Series

ScopeMeter® 120 Series: Three-in-one simplicity

The compact ScopeMeter 120 Series is the rugged solution for industrial troubleshooting and installation applications. It’s a truly integrated test tool, with oscilloscope, multimeter and “paperless” recorder in one affordable, easy-to-use instrument. Find fast answers to problems in machinery, instrumentation, control and power systems.

Features:
* Dual-input 40 MHz or 20 MHz digital oscilloscope
* Two 5,000 counts true-RMS digital multimeters
* Automatic measurements
* A dual-input TrendPlot™ recorder
* Connect-and-View™ trigger simplicity for hands-off operation
* Shielded test leads for oscilloscope, resistance and continuity measurements
* 10:1 Voltage Probe included with Fluke 124 and 125 for high frequency measurements
* Up to 7 hours battery operation
* 600 V CAT III safety certified
* Optically-isolated interface for PC connection
* Rugged, compact case
* Fluke 125 gives bus health and power measurements

In today’s complex systems, a meter measurement just doesn’t give enough detail to determine the cause of a fault. Signal anomalies, dropouts and glitches that might cause a machine to go down, are best displayed with an oscilloscope. The ScopeMeter 120 Series meet today’s need of simultaneously measuring and checking waveforms. The unique Connect-and-View™ triggering automatically displays stable waveforms of virtually any signal. It really is as easy as one-two-three!

A three-in-one tool
ScopeMeter 120 Series combines a 40 or 20 MHz dual input digital storage oscillo-scope, two true-RMS digital multimeters and a dual input TrendPlot™ recorder all in a compact, battery powered instrument. Leave all other test tools behind, the ScopeMeter 120 Series is the only tool you’ll need

One test lead measures all
Check the starting capacitor of a motor using the ScopeMeter 120 Series
High frequency waveform-, meter-, capacitance- and resistance-measurements as well as continuity checks are all covered by the shielded test leads. No time wasted finding or swapping leads. The included accessories allow hook-up at test objects of every dimension.

The confidence to do a better job
Working under time pressure and in cramped or difficult to reach locations means you want to focus on the job at hand, not on the test tool in your hand. Which is why the ScopeMeter 120 Series has Connect-and-View automatic triggering.You don’t have to worry about triggering and instrument settings, and you have all the information on screen to do the job right.

Battery powered mobility
Up to seven hours of battery operation frees you from mains outlets for true on-the- move working. The handheld format and the weight of just 1.2 kg, make the instrument easy to carry and to fit comfortably in your hand. The rugged and drip proof case assures long life and reliable operation in the harshest industrial environments.

Floating measurements, safety certified
While conventional oscilloscopes can only make measurements referenced to power line ground, the Fluke 120 Series make floating measurements so there is no risk of an accidental ground short circuit when making a connection. The ScopeMeter 120 Series and the included shielded test leads are safety certified for measurements on 600 V CAT III industrial power systems. And using the VPS40 probe, measurements up to 1000 V CAT II re fully supported! Via the optically isolated RS-232 or USB interface, the ScopeMeter 120 Series can be safely connected to a printer for direct print-out or to a PC for later analysis and documentation using FlukeView software.

Connect-and-View™ triggering for an instant, stable display
Scope users know how difficult triggering can be. Wrong settings show unstable and sometimes wrong results. Fluke’s unique Connect-and-View recognizes signal patterns, and automatically sets up correct triggering. It provides a stable, reliable and repeatable display of virtually any signal - including motor drive and control signals - without you touching a button. Signal changes are instantly recognized and settings adjusted for a stable display. Benefit from the speed and convenience when measuring a number of test points in quick succession.

Use TrendPlot™ to help find intermittents, fast
The toughest faults to find are those that happen only once in a while: intermit-tents. They can be caused by bad connections, dust, dirt, corrosion or simply broken wiring or connectors. You may not be around to see it — your Fluke ScopeMeter will. In this “paperless recorder” mode, you can plot the minimum and maximum peak values and average over time – up to 16 days. The two inputs can plot any combination of volts, amps, temperature, frequency and phase - with time and date stamp -to help lead you to the cause of those faults quickly.

Based on the 124, the Fluke 125 offers additional test capabilities for measurements on industrial machinery and industrial buses. The Bus Health Test capabilities are discussed in a separate section, see here.

Furthermore, the 125 offers the following additional capabilities for tests on industrial machinery:
* Power Measurements for single phase and balanced 3-phase systems. The Fluke 125 can directly present you the Total Power (Watts), Apparent Power (VA), Reactive Power (VAR) and the Power Factor (PF), over a wide range of applied frequencies, including those seen with motor drives and inverters. As a result, you are able to easily see the effects on the various power measurements during start-up or under changing operational conditions. A current clamp is included as a standard.
* Harmonics mode graphically displays harmonics up to the 33rd harmonic to assist in fault-finding, e.g. with large non-linear loads.
* RPM and Hz reading for use with electrical and combustion engines.
* Vac pwm for use on motor drive outputs, reading the true output voltage experienced by the motor itself.
* Low impedance measurements giving a 0.01 ohms resolution for motor windings and the like.

FlukeView® Software for documenting, archiving and analysis
FlukeView® for Windows® helps you get more out of your ScopeMeter by:

* Documenting - transfer waveforms, screens and measurement data from the ScopeMeter to a PC. Print or import the data into your report.
* Add user text to individual ScopeMeter settings – providing guidance to the operator when recalling a set-up.
* Archiving - create a library of waveforms with your comments for easy reference and comparison. Store complete Replay cycles for analysis of waveform changes. Store complete memory content of the ScopeMeter on your PC for back-up purposes.
* Waveform Compare – store reference waveforms on the PC, or send a reference back to the ScopeMeter for waveform comparison and “Pass/Fail” testing.
* Analysis - use cursors, perform spectrum analysis or export data to other analysis programs. ScopeMeter test tools are connected to a PC via an optically-isolated RS-232 or USB interface cable.

fluke_123.jpg

fluke_124.jpg

fluke_125.jpg

IRtek IR100e Portable Infrared Thermometer

chris — Mon, 24 May 2010 07:33:39 +0000

IRtek IR100e Portable Infrared Thermometer

Specifications:
Measurement Range: -25ºC ~ 1000ºC (-13ºF ~ 1832ºF)
Distance : Spot: 50 : 1
Resolution: 0.5º
Accuracy: ±0.5% of reading or ±1ºC which is greater
Emissivity: adjustable 0.10 ~ 1.00
Response Time: ≤ 500ms
Spectral Response: 7 ~ 18µm
Laser Pointer: Single, Class II, up to 1mW
Power: 9V battery
Size: H165 x D30 x W105 mm
Weight: 200g
Standard Accessories: Hard Case, Instruction Manual, Batteries, Certificate of Product Conformance

irtek_IR100e.jpg

ATTEN APS3005S Single Output Adjustable Power Supply (30V-5A)

admin — Sat, 06 Nov 2010 14:42:33 +0000

ATTEN APS3005S Single Output Adjustable Power Supply

Light and Compact Design
Ideal for Educational Laboratories. Safe for students to use
0.01% High Regulation
Constant Voltage and Constant Current Operation
Internal Select for Continuous or Dynamic Load
Low Ripple and Noise
Overload and Reverse Polarity protection
Customized design available

Specifications:
Rated Output Voltage: 0-30V ( Adjustable )
Rated Output Current
APS 3003S : 0-3 A (Adjustable)
APS 3005S : 0-5 A (Adjustable)
Rated Output Power: 90W
Voltage Accuracy: ± 0.5% Rdg +2bit
Current Accuracy: ± 0.5% Rdg +2bit
Ripple And Noise: ≤ 3mvrms (Test Conditions 30V / 3A)
Load Stability: ≤ 0.3% (Test Conditions 30V / 3A)
Digital Display Resolution: Voltage 0.1V Current 0.01A
Protection Methods:
Current Limited Lower Voltage
Short Circuit Protection
Over-Temperature Protection
High-pressure Test: Leakage Current ≤ 1ma (Test Conditions: Input-To-Ground 1700VAC/2s)
Insulation Resistance: Insulation Resistance ≥ 7MΩ (Test Conditions: Input-To-Ground 500VDC/5s)
Work Method: Constant-Current Constant-Voltage
Cooling Method: Strong Wind Cooling
Working Environment: 0-40 ℃; Relative Humidity <80%
Storage Temperature: -20-80 ℃ Relative Humidity <80%
Size: 260 * 150 * 160 (L * W * H)

atten_aps3003s.jpg

Lutron DW-6060 Digital Watt Meter

chris — Fri, 20 Mar 2009 16:31:48 +0000

Lutron DW-6060
Digital Watt Meter

Spesifikasi :
-WATT (AC, true power) : 2000 W, 6000 W.
-DCV, ACV, DCA, ACA.
-DC 9 V battery power, 13 mm LCD.
-Size : 180 x 86 x 35 mm.

DW-6060.jpg

Kyoritsu 2031 Digital Clamp Meter

chris — Sun, 12 Apr 2009 14:59:23 +0000

Kyoritsu 2031 Digital Clamp Meter

Features :
• Can measure large AC current up to 200A.
• 24mm-dia tear drop shaped jaws.

Specifications :
AC A : 20A
±2%rdg±5dgt [50Hz~1kHz]
200A
±2%rdg±5dgt [50/60Hz]
±3%rdg±10dgt [40Hz~1kHz]
Conductor Size : Ø24mm max.
Safety Standard : IEC 61010-1 CAT.III 300V
Frequency Response : 40Hz~1kHz
Withstand Voltage : 3700V AC for 1 minute
Power Source : LR-44 (1.5V) × 2
Dimensions : 147(L) × 58.5(W) × 26(D)mm
Weight : 100g approx.
Accessories : 9090 (Carrying Case)
LR-44 × 2
Instruction Manual
Optional : 8004/8008 (Multi-Trans)

kyoritsu-2031.jpg