Alat Ukur & Analisa

IMR CD100A Combustible Gas Leak Detector

chris — Thu, 12 Jan 2012 05:37:37 +0000

IMR CD100A Combustible Gas Leak Detector

The CD100A is designed to detect combustible gas leaks in residential and small commercial applications.
It is small, easy to use and has a 18" long flexible gooseneck for hard to reach areas.

* Simple adjustable tick rate increases as the sensor tip approaches a leak
* Audio and visual tick rate, fully adjustable
* Easy one hand operation
* Long 18" (45cm) gooseneck for hard to reach areas
* 'Tip Light' in sensor cover illuminates the area of the leak
* Rubber boot protects instrument
* Sensor provides accurate detection
* Headphone jack
* Separate battery compartment for quick and easy battery replacement

Partial list of gases sensed:
Acetone, Alcohol, Ammonia, Benzene, Butane, Gasoline, Halon, Hydrogen Sulfide, Industrial Solvents, Jet Fuel, Laquer Thinners, Methane, Naphta, Natural Gas, Propane, Refrigerants, Toluene... and more.

imr_cd100a.jpg

Geotech G150 Indoor Air Quality Analyser (CO2)

chris — Sat, 31 Dec 2011 03:36:25 +0000

Geotech G150 Indoor Air Quality Analyser (CO2)

New CO2 analyser designed to monitor CO2 for all indoor air quality applications. This unit has been developed to incorporate the latest technology and specification requirements to provide the user with a fast, simple to use and accurate piece of environmental field kit.

Features and benefits
* CO2 0-10,000 ppm
* Options for: O2 0-100%, dual temperature probes 0 - 50oC, data storage and download, humidity sensor 0 - 100%
* Improved accuracy on CO2 readings
* Quick verification of CO2 levels for site audits
* Easy to read display
* Built-in gas moisture removal

Applications
* General IAQ
* Environmental Site Audits
* HVAC System approval
* Illegal immigrant control/detection

geotech_g150.jpg

Gaztox Oxygen and Toxic Gas Detector

chris — Sat, 31 Dec 2011 03:32:37 +0000

Gaztox Oxygen and Toxic Gas Detector

Depending on the type of sensor fitted this single gas detector measures hazardous concentrations of oxygen, or toxic gases such as hydrogen sulphide, carbon monoxide, sulphur dioxide. The Gaztox is an essential tool for on-site safety of landfill and biogas professionals. ATEX certified zone 0.

Features
* Audio alarm (95dB)
* Visual LED alarm
* Rugged and lightweight
* Wide, easy to read LCD screen
* Optional accessories
* Water resistant (IP67)
* ATEX certified

Benefits
* Easy to use
* Robust and compact design
* Powerful alarms
* Low maintenance

Applications
* Waste disposal centres
* Water treatment works
* Power stations
* Petrochemical industry

gaztox.jpg

Aquaread AP900 Water Quality Meter

chris — Sat, 31 Dec 2011 03:26:37 +0000

Aquaread AP900 Water Quality Meter

The new hand-held meter from Aquaread Ltd is the most sophisticated yet easy to use multi-parameter water quality test system. The reader is rugged, waterproof and small enough to fit in the palm of your hand.

Benefits
* Easy calibration
* Hand-held, lightweight and rugged
* Long-term data logging
* Easily attached, lengths up to 100m deployment
* Fast (1 second) onsite response
* Aqualink software compatible with Google Earth maps

Features
* IP67 rated meter
* Narrow 42mm diameter
* Up to 10 parameters displayed
* Probe is marine grade aluminium
* Flow cell option for low ground water sampling
* GPS location and ID stamping
* Hard carry case available for added protection

Applications
* PPC permitting
* Landfill
* Rivers
* Groundwater sampling
* Brownfield

aquaread.jpg

Hioki LR5001 Humidity Logger

chris — Thu, 08 Dec 2011 07:24:16 +0000

Hioki LR5001 Humidity Logger

Features:
* Easily mount the light-weight , pocket-sized loggers in tight spaces
* Easy-to-see dual display
* Transfer data to PC even during recording
* Replace batteries while recording(30 second limit)
* Record 60,000 data per channel
* Record without missing fluctuations in STAT mode
* Measurement data is preserved even after the battery dies
* Worry-free backup preserves recorded data even if a new measurement is started by mistake

hioki_lr5001.jpg

Hioki LR5011 Temperature Logger

chris — Thu, 08 Dec 2011 07:22:51 +0000

Hioki LR5011 Temperature Logger

hioki_lr5011.jpg

Hioki LR5041/Hioki LR5042/Hioki LR5043 Voltage Logger

chris — Thu, 08 Dec 2011 07:20:07 +0000

Hioki LR5041/Hioki LR5042/Hioki LR5043 Voltage Logger

hioki_lr5041.jpg

Piecal 334 DC Milliamp Loop Calibrator

chris — Sat, 03 Dec 2011 13:41:42 +0000

Piecal 334 DC Milliamp Loop Calibrator

Features:
* Calibrate Milliamp Instruments
Source 0.00 to 24.00 mA & -25.0 to 125.0% of 4-20 mA
Read 0.00 to 52.00 mA
Read -99.99 to 99.99 V
Simulate 2-Wire Transmitters; Power & Read 2-Wire Transmitters
* Calibrate with Confidence
Accurate to ±0.025% of Span at 4.00 & 20.00 EZ-CHECK outputs
* Use in the Plant, Field or Shop
Includes Rubber Boot and Attached Test Leads; Low profile switches resist accidental damage
* Simple Battery Changes
Separate compartment for no-tool battery changes with four inexpensive "AA" batteries
* Optional Accessories
AC Adaptor 120V (020-0101); 240V (020-0100); Carrying Case (020-0205); NiMh Batteries & Charger 120VAC/12V DC (020-0103)
Improvements over 334s from other manufacturers include better longer term stability, accuracy, reliability & ruggedness plus improved battery life. PIECAL 334 is the perfect replacement for your worn out mA calibrators!

piecal_334.jpg

Piecal 334Plus DC Milliamp Loop Calibrator

chris — Sat, 03 Dec 2011 13:35:27 +0000

Piecal 334Plus DC Milliamp Loop Calibrator

Features:
* Calibrate Milliamp Instruments
Source 0.00 to 24.00 mA & -25.0 to 125.0% of 4-20 mA
Read 0.00 to 52.00 mA
Read -99.99 to 99.99 V
Simulate 2-Wire Transmitter, Power & Read Transmitters
Menu Selectable 250 Ohm resistor for HART compatibility
* Calibrate with Accuracy
Accurate to ±(0.02% of Reading + 0.002 mA)
* Easty-to-Read Backlit Display
* Locate Loop Current Leakages
Automatic indication of Loop Current and Leakage Current. Measure ground current leakage from faulty wiring, flooded conduit and corrosion bridges. Leakage typically appears as a Zero Shift and helps you decide if the transmitter needs calibration or if there is a problem in the loop wiring.
* Faster Calibrations
Three output EZ-CHECK switch
2 speed EZ-DIAL
Stepping & Ramping
* Includes Rubber Boot & Test Leads
* Optional Accessories
AC Adaptor 120 V (020-0101); 240 V (020-0100)
NiMh Batteries & Charger 120 VAC/12V DC (020-0103)

piecal_334plus.jpg

Piecal 434 High Accuracy Milliamp Loop Diagnostic Calibrator

chris — Sat, 03 Dec 2011 13:32:19 +0000

Piecal 434 High Accuracy Milliamp Loop Diagnostic Calibrator

Features:
* Calibrate Milliamp Instruments
Source 0.000 to 24.000 mA & -25.00 to 125.00% of 4-20 mA
Read 0.000 to 24.000 mA & -25.00 to 125.00% of 4-20 mA
Read -99.99 to 99.99 V
Simulate 2-Wire Transmitter, Power & Read Transmitters
Menu Selectable 250 Ohm resistor for HART compatibility
* Calibrate with Lab Accuracy
Accurate to ±(0.01% of Reading + 0.002 mA)
PIECAL 434 is more accurate than similar calibrators - within ±0.004 mA at 20 mA output!
* Easty-to-Read Backlit Display
* Locate Loop Current Leakages
Automatic indication of Loop Current and Leakage Current. Measure ground current leakage from faulty wiring, flooded conduit and corrosion bridges. Leakage typically appears as a Zero Shift and helps you decide if the transmitter needs calibration or if there is a problem in the loop wiring.
* Faster Calibrations
Three output EZ-CHECK switch
2 speed EZ-DIAL
Stepping & Ramping
* Includes Rubber Boot & Test Leads
* Optional Accessories
AC Adaptor 120 V (020-0101); 240 V (020-0100)
NiMh Batteries & Charger 120 VAC/12V DC (020-0103)

piecal_434.jpg

Piecal 134 Pocket-Mate mA Loop Calibrator

chris — Sat, 03 Dec 2011 13:30:13 +0000

Piecal 134 Pocket-Mate mA Loop Calibrator

Features:
* Calibrate Milliamp Instruments
Source & Read 0.00 to 24.00 mA & -25.00 to 125.0% of 4-20 mA
Simulate 2-Wire Transmitters; Power & Read 2-Wire Transmitters
Selectable 250 Ω resistor for HART compatibility
* Calibrate with Confidence
Accurate to ±(0.05% of reading at 0.01 mA)
* Compact & Affordable
Pocket sized with built-in belt clip & attached test leads
Includes two "AA" batteries
* Faster Calibrations
Instantly select three outputs with EZ-CHECK switch & two speed EZ-DIAL knob
* Optional Accessories
Carrying case with belt clip (020-0200)

piecal_134.jpg

Piecal 532 4-20 Milliamp/Voltage Loop Calibrator Diagnostic

chris — Sat, 03 Dec 2011 13:27:32 +0000

Piecal 532 4-20 Milliamp/Voltage Loop Calibrator Diagnostic

Features:
* True ±0.012% of reading accuracy
* Source and Read 0.000-24.000 mA
* Simulate 2-Wire Transmitters
* Power 2-Wire Transmitters and Read 0.000-24.000mA
* Display current in mA or -25.00-125.00 % of 4-20 mA
* Read 0.00 to ± 30.00 VDC with 4X over range ability
* Source 0.000 to 24.000 VDC with up to 20mA output
* Direct Calibration 1.000V to 5.000V
* Auto Step or Ramp
* Selectable step sizes, time in-between steps & soak time
* Stop watch like EZ-Check™ switch
* Full 5 Digit Display
* Uses 1 – 9Volt alkaline battery
* Superior battery life of 40 hours under typical continuous usage
* Easy access to battery compartment
* 240 VAC Tolerant
* HART® protocol compatibility mode
* Power on selectable 250Ω resistor in series with the output for compatibility with HART® protocol enabled devices.
* AC adaptor, carrying case, and Test Data available

piecal_532.jpg

Piecal 535 4-20/10-50 Milliamp/Voltage Dual Range Loop Calibrator

chris — Sat, 03 Dec 2011 13:23:25 +0000

Piecal 535 4-20/10-50 Milliamp/Voltage Dual Range Loop Calibrator

Features:
* True ± 0.025% of reading
* Read and Source 0.000 to 50.000 mA
* Display current or -25.00 to 125.00% of 4-20mA or 10-50mA
* Bar graph displays % of 4-20mA or 10-50 mA
* Read 0.00 to 60.00 volts with 2X over range ability
* Simulate 2-Wire Transmitters
* Power 2-Wire Transmitters and Read 0.000-50.000mA
* Read 0.00 to ± 30.00 VDC with 4X over range ability
* Source 0.000 to 24.000 VDC with up to 20mA output
* Direct Calibration 1.000V to 5.000V
* Loop Compliance Voltage ≥ 43 Volts
* OPTIONAL ANALOG OUTPUT for chart recorders & Data loggers
* Auto Step or Ramp with HIGH accuracy and repeatability designed in collaboration with Nuclear plants
* Selectable step sizes, time in-between steps & soak time
* Stop watch like EZ-Check™ switch
* Full 5 Digit Display
* Fuseless protection from accidental connection to 240 volts AC/DC
* Rugged handheld enclosure with optional lanyard and Velcro® hand strap
* Uses 4 AA alkaline batteries
* Superior battery life of 40 hours under typical continuous usage
* Easy access to battery compartment
* AC adaptor, carrying case, and Test Data available

piecal_535.jpg

Piecal 525 T/C & RTD Dual Calibrator

chris — Sat, 03 Dec 2011 13:20:06 +0000

Piecal 525 T/C & RTD Dual Calibrator

Features:
* Accurate to ±0.2°C (±0.4°F) with 0.1° or 0.01° Resolution
* Direct Temperature Input/Output
* Eight Standard T/C Types available - J, K, E, T, R, S, B, N and mV
* Eight RTD Curves available - Platinum, Copper, Nickel & Ω
PATENT PENDING AUTO DETECTION OF 2, 3, OR 4 WIRE CONNECTION INDICATOR
* Guaranteed to Work with All Pulsed Instruments
* Works with a wide variety of transmitters including popular * Rosemount and Honeywell Models
* Compatible with devices using pulsed excitation currents including PLCs, DCS, Recorders, and all others
* EZ-Dial™ knob easily adjust output by 0.1°
* Pressing down and turning will select a faster dialing speed
* EZ-Check™ switch for 0% and 100% span adjustments
* Store new EZ-Check™ values by pressing the EZ-Dial™ Knob
* Selectable Auto Stepping
* Uses a standard 9V Alkaline Battery
* Superior battery life of 45 hours under typical continuous usage
* Easy access to battery compartment
* Lightweight, Rugged and Reliable
* Small, tough and protected to 60V
* Wire kits, carrying case, and Test Data available

piecal_525.jpg

Piecal 322-1 Automated Thermocouple Calibrator

chris — Sat, 03 Dec 2011 13:17:39 +0000

Piecal 322-1 Automated Thermocouple Calibrator

Features:
* Source and Read Four T/C Types plus mV
J, K, T & E: -13.000 to 80.000 mV
* Calibrate with Confidence
Resolution to 0.1 °F & °C; Accurate to 0.2°
* Faster Calibrations
Instantly select three outputs with EZ-CHECK switch
Easily find trip points with two speed EZ-DIAL knob & Automatic Stepping
* Easily Change T/C Types & Scale
Double click to select T/C type & °F & °C
* Easy-to-Read Display
Turn on the backlight to read in dark areas of the plant
* Use in the Plant, Field or Shop
Includes Rubber Boot and mV Test Leads
Low profile switches resist accidental damage
* Simple "No Tool" Battery Changes
Four inexpensive "AA" batteries
* Optional Accessories
Wire & Mini T/C Plug: J, T, E, K (020-0202)

piecal_322.jpg